No codes. Did a PCM reset but no codes

 

This is a weird one for sure it has to be something in the connector broken wire or loose pin since it worked before and now both tb are inop and non responsive

Do you know how to disassemble the plug its a bit tricky and if not done correctly pins won't stay in it when done then you would really be SOL I wish I was closer you need to check for a damaged wire it's likely I'm sure in your struggle to unplug it damage happened

 

Try having someone hold the connector tightly to the tb while you try to start the truck. I would do a batt reset for 2 min first.

 

You should be able to buy a tb repair harness/plug and Repin the new one.

 

Keith you are the man!! Was out there at 7am pulling it back apart an found that I bent one of the pins in the tb. Straightened it out an now all seems good. That was a nightmare. But simple fix. Excuse me but I feel the need to do a 0-100 pull right about now.

 

Nice
:bow::bow: :thumb:

 

Plug repair kit or salvage yard.

Repair Kits

 

Greg that's a great link thanks for that!

 

Bent prong in the stock TB, doh!

 

Yea I know... When i took everything apart this morning I looked at the tb an saw it, I kinda laughed. Something that simple an turns out to be a pain in the ***. I didn't want to have to drive the Ranger again!

 

Glad you got it fiqured out. Bent pin is easier to fix than a broken wire. Ok!!! you played around enough, now get that ported TB on. lolol

 

Yep retest now no more bent pins

 

That's great news Mario. :thumb::thumb: How did the 0 to 100mph go?

 

Truck feels like poo. Ran rough at first just like intial start up after cam swap so I drove it around town to do errands an it felt better. Had to two foot it for a couple miles after it died at a light but holds an idle now.

 

That's because you reset the adaptive's back to square 1. Also your running on a canned tune. If you had a custom tune it would run alot better from the start. It's not a fail, just a bump in the road of modding. There's probably nobody on here with a modded truck that isn't saying, yep been there done that, on atleast one of their mod's. lolol

 

That's because you reset the adaptive's back to square 1.

:iagree:100% Your engine/trans is relearning again. Just cruise around town and it will get better as the engine settings are adjusted. Drive it for about 30 to 40 minutes and the computer will make the adjustments after the truck sits and cools down. Let it sit for 2 1/2 to 3 hours. If it's not idling correctly. Do stop and go driving for the computer to receive and make adjustments after the truck is cooled down again. Also, don't forget to do some freeway driving. Don't beat on the truck until the computer has made the adjustments to the engine and trans. Every time you do a computer reset or disconnect the battery. You will have to do computer learning/adjustment driving with our trucks.

After swapped to the KRC rv cam. The truck ran like crap too but, got much better after drive it for a few days. Was told later on that the truck has an adaptive computer. Always makes adjustments to your driving conditions. Just makes adjustments at a much slower rate. Hang in there Mario.:thumb:

Note: I have to let the computer relearn/adjustment driving every time the battery has been disconnected on my truck. "Even with a custom tune".:blink: The battery is disconnected right now.......:ermm:

 

Think I may just write this as a FAIL. Time to stop messing around an get with the other mods

 

There you go... Ported throttle bodies are a joke just like a TB spacer.

Get the Ypipe so we can get to work on converter and longtube install.

 

Get the Ypipe so we can get to work on converter and longtube install.

:iagree::thumb::thumb:opcorn:

 

Thanks for the help guys. An Tyler that's the plan

 

Get to it, stop being responsible.

 

Ya, what Tyler said...... It's much better to be irresponsible.

 

:thumb:

 

Sure hope to have my goodies on by the end of the year..

 

How did the throttle body work out ?

 

Never tried putting it back on. It's sitting in the garage at my parents ill mess with it one of these days. But I'm taking a break from the truck for a just a lil bit. I will be coming with some new things soon tho

In the end tho I think I bored to much

 

I bet once you put the headers on it won't be to much.