[Ghost03hemi]

Just a little port matching is needed. There's even a dome in the ceiling of the port for a cone spray injector. Really like this intake manifold so far.

 

[Ghost03hemi]

A little bit of port matching needed for the throttle body adapter. This is the stock 80mm tb.

 

[Ghost03hemi]

The supplied bolts are too short for the stock 80mm tb.

 

[Ghost03hemi]

The top O-ring seams to be a little small in diameter. The bottom o-rings are robust and should seal good. Fit snug, so they should stay in place when installing the intake manifold onto the cylinder heads.

 

[Ghost03hemi]

It comes with intake manifold studs.

 

[Ghost03hemi]

Very nice fuel rails.

 

[Rays04GTX]

for the Head mounting flange..............
for the day to day Ram Nutz ,

Cometic C5197 Cometic Aramid Fiber Intake Gaskets | Summit Racing

Free Shipping - Cometic Aramid Fiber Intake Gaskets with qualifying orders of $99. Shop Intake Manifold Gaskets at Summit Racing.

www.summitracing.com

For the ALL out Ram Nutz.

Dodge/Chrysler 6.1L Hemi Intake Manifold Gasket | Thermal Heat Shielding Gasket

those "holley O rings" are the are the foundation of many a Headache.

As for the top......... the rubber "o" ring cord works the best.....a little Permatex 85420 won't hurt

 

[Rays04GTX]

for the Head mounting flange..............
for the day to day Ram Nutz ,

Cometic C5197 Cometic Aramid Fiber Intake Gaskets | Summit Racing

Free Shipping - Cometic Aramid Fiber Intake Gaskets with qualifying orders of $99. Shop Intake Manifold Gaskets at Summit Racing.

www.summitracing.com

For the ALL out Ram Nutz.

Dodge/Chrysler 6.1L Hemi Intake Manifold Gasket | Thermal Heat Shielding Gasket

those "holley O rings" are the are the foundation of many a Headache.

For anyone who wants to use the Sniper series Intakes.......DO NOT use the "o" rings supplied ...use one of the two gaskets above .

 

[charged392]

Already got a set myself for my setup. I have heard of leaks being an issue

 

[Ghost03hemi]

DO NOT use the "o" rings supplied ...use one of the two gaskets above .

Yes, planned to use gaskets as well. Thanks Ray.

 

[Ghost03hemi]

As for the top......... the rubber "o" ring cord works the best.....a little Permatex 85420 won't hurt

Also check the machined surface for shipping dings. Thanks again Ray.

 

[Ghost03hemi]

Little cheaper as long as ordering RTV and a few other things with it..

2009 DODGE CHALLENGER Sikky Manufacturing TN-044A Sikky Manufacturing Thermalnator Intake Manifold Gaskets | Summit Racing

Free Shipping - Sikky Manufacturing Thermalnator Intake Manifold Gaskets with qualifying orders of $99. Shop Intake Manifold Gaskets at Summit Racing.

www.summitracing.com

 

[Ghost03hemi]

Holley Hi-Ram spec's. It should clear with no problems at the over hang of the fire wall.

 

[04sthemi]

Stu, have you made a pass in this truck?

 

[Ghost03hemi]

Yes, but was not happy with the results.

 

[Ghost03hemi]

Ordered new con rod bearings from Callies Performance Products. Had the original invoice with part numbers. This is what showed up. Not even close to the part # or order #...

 

[Ghost03hemi]

Finally got some time to work on the engine. Will have to mod the wiring harness for the new intake manifold.

 

[Ghost03hemi]

Will have to mod the map sensor location. This will hit the fire wall.

 

[Ghost03hemi]

Does Mopar have a 2bar map that is 90 degree and works on a 2003-2005 Hemi Ram truck?

 

[arocketman]

Might have to dimple the firewall Stu.