Heads - Hemi Truck Club
 
Go Back   Hemi Truck Club > State Chapters of HTC.com > Florida Chapter

Reply
 
Thread Tools Display Modes
 
Old 01-04-2014, 08:17 PM   #1
2012 Truck of the Year
Engine Specialist
 
charged392's Avatar
 
Join Date: May 2011
Location: Fort pierce, FL
Posts: 17,312
Garage
Heads

As you may know my heads are done for been running low 12s limping on most cylinders due to valve stem wear so I am throwing this out there does anyone know where I can find a set of heads used damaged whatever for a rebuild/port job and roller assembly

I keep fouling plugs out on #2/5/8 cylinders so far just had to change #2 today from a hard start issue the stem wear is very bad completely unreal

__________________
"CMR TUNER" [email protected] 1/4 with a 7.32 1/8 custom long/short bars by "Me" Turbocharged 392 on 9psi S475/96/1.32 . Running thru an A518! [email protected]
charged392 is offline   Reply With Quote
Sponsored Links
Advertisement
 
Old 01-04-2014, 09:17 PM   #2
Senior Member
 
FASTHEMIRAM05's Avatar
 
Join Date: Oct 2009
Location: Orlando, FL
Posts: 2,360
Austin has a Pair
__________________
Modern Performance Engineering
Had 2002 4.7 RCSB 14.2
Had 2011 RCSB 12.41
Had 2012 RCSB 13.99
Had 2016 QCSB 13.0
2011 Drag Truck....

FASTHEMIRAM05 is offline   Reply With Quote
Old 01-04-2014, 11:01 PM   #3
Senior Member
 
Carrolls Ram's Avatar
 
Join Date: Sep 2009
Location: Orlando, FL
Posts: 1,298
True story
__________________
__________________________
2015 Ram 2500 CTD CCSB 4x4
07 Turbo Ram: Sold
Carrolls Ram is offline   Reply With Quote
Sponsored Links
Advertisement
 
Old 01-05-2014, 07:56 AM   #4
Stu
 
Join Date: Oct 2009
Location: FL
Posts: 20,454
Garage
Aren't you running big valve heads already Keith?

Don't take this the wrong way but, are you sure it's not the Diamond pistons? Pull those spark plugs and take a camera to the cylinders....... When I toasted my Diamond pistons, it fouled plugs too.
Ghost03hemi is offline   Reply With Quote
Old 01-05-2014, 08:47 AM   #5
2012 Truck of the Year
Engine Specialist
 
charged392's Avatar
 
Join Date: May 2011
Location: Fort pierce, FL
Posts: 17,312
Garage
These heads I am running are the stock 2003 heads nothing was done to them except deck a tiny bit so there would be no gasket issues they have well over 156k on them and are completely shot
__________________
"CMR TUNER" [email protected] 1/4 with a 7.32 1/8 custom long/short bars by "Me" Turbocharged 392 on 9psi S475/96/1.32 . Running thru an A518! [email protected]
charged392 is offline   Reply With Quote
Old 01-05-2014, 10:06 AM   #6
Senior Member
 
Carrolls Ram's Avatar
 
Join Date: Sep 2009
Location: Orlando, FL
Posts: 1,298
Ones I have are off an 06? 300c. 1 chamber is messed up but the other head is good. Was going to port them but lost interest
__________________
__________________________
2015 Ram 2500 CTD CCSB 4x4
07 Turbo Ram: Sold
Carrolls Ram is offline   Reply With Quote
Old 01-05-2014, 01:34 PM   #7
2012 Truck of the Year
Engine Specialist
 
charged392's Avatar
 
Join Date: May 2011
Location: Fort pierce, FL
Posts: 17,312
Garage
How badly is it messed up? And do you want to get rid of them?
__________________
"CMR TUNER" [email protected] 1/4 with a 7.32 1/8 custom long/short bars by "Me" Turbocharged 392 on 9psi S475/96/1.32 . Running thru an A518! [email protected]
charged392 is offline   Reply With Quote
Old 01-05-2014, 03:33 PM   #8
Slow Memeber
 
04sthemi's Avatar
 
Join Date: Oct 2011
Location: S.Daytona
Posts: 5,470
I wish I had the coin to pick up some heads too.
__________________
04sthemi is offline   Reply With Quote
Old 01-05-2014, 04:57 PM   #9
Senior Member
 
Carrolls Ram's Avatar
 
Join Date: Sep 2009
Location: Orlando, FL
Posts: 1,298


Heres the damaged one



__________________
__________________________
2015 Ram 2500 CTD CCSB 4x4
07 Turbo Ram: Sold
Carrolls Ram is offline   Reply With Quote
Old 01-05-2014, 05:45 PM   #10
2012 Truck of the Year
Engine Specialist
 
charged392's Avatar
 
Join Date: May 2011
Location: Fort pierce, FL
Posts: 17,312
Garage
That's not bad at all can be smoothed out
__________________
"CMR TUNER" [email protected] 1/4 with a 7.32 1/8 custom long/short bars by "Me" Turbocharged 392 on 9psi S475/96/1.32 . Running thru an A518! [email protected]
charged392 is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


» Premium Vendor Showcase
n2 Speed Edge InTune Edge OCPerformance Parts

All times are GMT -6. The time now is 02:27 AM.


Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.